How big is too big? Notching and boring rules for dimensional lumber joists

Every carpenter, electrician, plumber, HVAC contractor, and home inspector should know the rules for allowable cuts and holes into floor joists. Cuts and holes are known in the trades as notching and boring, respectively. The rules for notching and boring come from section 502.8 of the International Residential Code, which addresses cutting, drilling, and notching. Today I’m only focused on traditional dimensional lumber, like 2x8s or 2x12s. I’ll discuss holes in manufactured floor joists, aka I-joists, in next week’s blog post.

Rules for boring/drilling holes

To start, here’s the diagram that comes right out of the codebook.

Bore holes

You can put holes in floor joists anywhere along the length of the joist, but you can’t put them any closer than 2″ from the top or bottom edge of a joist. The maximum size of a hole is 1/3 the depth of the floor joist. Dimensional lumber will always be a little smaller than the stated dimension unless you’re dealing with some ancient lumber. For example, a 2×4 actually measures 1-1/2″ x 3-1/2″. For floor joists, here are the maximum hole sizes for common floor joist sizes:

  • 2×6 (5-1/2″) ~ 1-13/16″
  • 2×8 (7-1/4″) ~  2-3/8″
  • 2×10 (9-1/4″) ~  3-1/16″
  • 2×12 (11-1/4″) = 3-3/4″

If you’re dealing with rafters, these same rules apply.

Rules for notching

The codebook has two diagrams for notching; one at the ends of the joist, and another for notching anywhere else. Let’s start with the easier one, notching at the ends.

Notches at ends of joists

You’re allowed to notch 1/4 of the joist depth at the end of a joist. For some common sizes, here are the maximum notches allowed:

  • 2×6 (5-1/2″) = 1-3/8″
  • 2×8 (7-1/4″) =  1-13/16″
  • 2×10 (9-1/4″) =  2-5/16″
  • 2×12 (11-1/4″) = 2-13/16″

For anywhere other than the ends, we use a different diagram.

Notches at top and bottom

You’re not allowed to do any notches in the middle third of a floor joist span, and you’re not allowed to notch the bottom side of members over 4″ in nominal thickness. For anything else, you’re allowed to notch 1/6 of the joist depth deep, and 1/3 of the joist depth wide. Here are the maximum numbers for some common sizes:

  • 2×6 (5-1/2″) ~7/8″ deep, 1-13/16″ wide
  • 2×8 (7-1/4″) ~  1-3/16 deep, 2-3/8″ wide
  • 2×10 (9-1/4″) ~ 1-1/2″ deep,  3-1/16″ wide
  • 2×12 (11-1/4″) = 1-7/8″ deep, 3-3/4″ wide

Summary

When any of these rules are violated, it’s a judgment call. When these rules a fudged just a little bit, I usually don’t make a big deal about it, especially if it looks like it has been that way for a long time. These numbers always assume the maximum loading for a floor, along with the maximum spacing of a floor joist. But when these rules are egregiously broken, that’s when it’s time to call in a carpenter for repairs. And note, I didn’t say to call in an engineer for further evaluation. This is basic floor framing, and any qualified carpenter ought to be able to make repairs without having to do a bunch of difficult math.

And just for fun, here are a few classics we’ve found over the years.

Notched joist

 

Written By

Reuben is a second-generation home inspector with a passion for his work. He grew up remodeling homes and learning about carpentry since he was old enough to hold a hammer. Reuben grew up thinking he was going to be a school teacher because he enjoyed teaching others so much. In a sense, that’s a lot of what home inspections are about, so Reuben truly does what he loves. Sharlene has worked with Structure Tech since 2000 and Reuben has been contributing to her blog since 2008.

Subscribe to Our Newsletter for Market Updates & Mid-Century Modern Listings

Our weekly HomesMSP Update includes current local market information and a curated list of mid-century modern properties for sale, plus posts from an inspector, a lender, a stager, info about neighborhoods, life in the Twin Cities… even recipes!

This field is hidden when viewing the form

Blog Categories

Archives

Sharon and John Hensrud

About Us

The HomesMSP Team is committed to meeting you where you are and listening… really listening to understand you so we can use our extensive knowledge of the market and local neighborhoods to give you personalized service.