Combustion Air

Everyone knows that oxygen is required for a fire, right?  So where does the oxygen come from for your furnace, gas water heater, fireplace, and other fuel-burning appliances?  Typically, this is supplied through a combustion air duct.  You’ll find combustion air ducts on all newer houses, and on many houses that have had new furnaces or water heaters installed.  While it was once thought that these ducts were not as necessary on older, drafty homes, newer research has shown that these leaks are not always reliable (and they are never desirable).

In homes that have bathroom exhaust fans and kitchen exhaust fans, especially the downdraft type, it is especially important to have a combustion air duct installed.  While combustion air ducts are not really intended to provide make-up air for exhaust fans, this is really what they end up doing, in addition to replacing the air that gets used by the fuel-burning appliances.  While it’s beyond the scope of this blog to get in to the specifics of how these are all inter-related, there are a couple of simple, but very important things to do as a homeowner.

  • Don’t block the duct opening.  This is the easiest, most obvious thing that you can do (or not do?).  The photo below shows a typical combustion air duct, with the opening un-obstructed.  You’ll feel cold air coming out of this duct on to the floor in the winter, but this is air that needs to come in to the house.  I’ve seen people tape the bottoms of these ducts shut, and I’ve seen rags stuffed in to the duct.  This is very bad idea, as carbon monoxide could be produced from lack of air.  To help keep cold air from dumping in to the house, a loop can be created at the bottom of the duct, or a bucket placed below it, as long as it doesn’t reduce the overall opening.

Dsc04269_3 Dsc04270_2

  • Make sure the intake is un-obstructed.  In Minnesota, the intake is required to be located at least 12” above grade, to help keep it clear from snow, leaves, and other debris.  If the intake is closer than this, consider having it raised.  If there is a damper installed at the opening at the exterior, remove it.  Dampers allow air out, not in! I’ve seen dampers installed on many homes when the vinyl siding installers didn’t know what the opening was for, so they installed a damper, which blocks the combustion air opening.

Combustion_air_inlet_too_close_to_2

  • Keep the intake clean.  This is something you should check at least once a year.  The intake will be located at the exterior of your home, and looks like the one pictured below.  There should be a 1/4 steel screen installed, which will keep larger pests from entering in to your home.  If this screen is dirty, clean it with a wet/dry vac.

Dirty_combustion_air_intake_2

When I perform home inspections for buyers, I check for all these things and a lot more!

Written By

Reuben is a second-generation home inspector with a passion for his work. He grew up remodeling homes and learning about carpentry since he was old enough to hold a hammer. Reuben grew up thinking he was going to be a school teacher because he enjoyed teaching others so much. In a sense, that’s a lot of what home inspections are about, so Reuben truly does what he loves. Sharlene has worked with Structure Tech since 2000 and Reuben has been contributing to her blog since 2008.

Related Posts

Transite Heat: is this a problem?

🖨 Print Article If you mention the word transite to about 90% of the population, they either think of HVAC ductwork installed below the concrete floor in a basement, or they...

Weekly real estate market update 3/22/24… about the NAR settlement

đź–¨ Print Article Coming soon listings, pending sales and multiple offers continue to increase. New listings dropped a bit this week but rising coming soon listings should have future impact...
1 Response

Subscribe to Our Newsletter for Market Updates & Mid-Century Modern Listings

Our weekly HomesMSP Update includes current local market information and a curated list of mid-century modern properties for sale, plus posts from an inspector, a lender, a stager, info about neighborhoods, life in the Twin Cities… even recipes!

Hidden

Blog Categories

Archives

Sharon and John Hensrud

About Us

The HomesMSP Team is committed to meeting you where you are and listening… really listening to understand you so we can use our extensive knowledge of the market and local neighborhoods to give you personalized service.